cone crusher oil leaking possible cause

Home > Ball Mill Process In Terms Of Mineral Processing > cone crusher oil leaking possible cause

Crushing Principle, Gear Wear and Solution of Cone Crusher

The hydraulic cone crusher handles secondary crushing in the production line, and specializes in processing of medium-hard materials. During the operation of the equipment, there will be problems such as tooth cracking, wear, jamming, and undercutting of the umbrella teeth, which will not only affect production, but also Cause direct or indirect economic losses.

What might cause cone crusher oil leakage-Jiaozuo zhongxin

Cone Crusher now has become the new darling of many mineral processing industry, with high yield and efficiency characteristics, but if you didn't pay attention to the daily operation, there will be some problems, so routine maintenance is very important. Oil spills, oil is relatively unusual rejection of a problem, the following Zhongxin briefly introduce the cause of the problem and the solution for you. The oil temperature is too high. Cause: The quality of the oil is poor or the oil is insufficient; the bearing is damaged; the ambient temperature is high, there is no cooling water or the cooling water pressure is low; the cooler is clogged. Oil temperature and pressure rise. Cause: The tubing or oil groove is clogged and the safety valve is faulty. Solution: Stop the machine, check and repair. Oil pressure is low after oil pump is started. Cause: The oil temperature is low; the pipe is blocked or the pump is running abnormally. Solution: Heat to increase oil temperature; repair pipe or oil pump. Oil contain lots of fine mud and impurities. Causes: failure of sealing dustproof device; water shortage caused by blockage or leakage of water pipe. People also ask Why does my cone crusher keep leaking water? Causes: water enters the lean oil station; the cooler leaks, and the water pressure is greater than the oil pressure; water supply too much or the return pipe is blocked. Cone Crusher Common Problems And How To Fix Them | M&C

If the working pressure of the cone crusher lubrication system is improper, the oil will be ejected from the shaft gap, causing the lubricating oil to leak downward along the outer circumference of the sealing cylinder. 5. The unreasonable gap between parts.

The Common Malfunction Of Cone Crusher - JXSC

Too much feed or the material unqualified may cause the stone crusher machine jam up. The machine works electricity too large lead to circuit automatic protection and stops the machine. Much more serious may turn up the machine halt because of jam up. And when there is iron ore or other unbreakable material in the cone crushing chamber, it also will cause jam up even get stuck.

What causes the sealing failure of the cone crusher_Jiaozuo

If the gap between the parts of the cone crusher becomes smaller, the seal will be squeezed and severely worn, or when the worn parts are replaced, due to the different wear cycles of the seals and frictional parts, the degree of newness and oldness Different, will also cause the sealing is not tight. The second is to check whether the seal is aging. The rubber seal is affected by oil quality and temperature for a long time, which will cause aging and make the seal have problems. Therefore

Oil Leakage Problem With Simons Cone Crusher

Oil Leakage Problem With Simons Cone Crusher If you are interested in our company's products, we welcome your consultation 7/24 hours, and we are committed to creating the most suitable solution for you.

miningeccentric bush of cone crusher failing causes - Products

Common Failure Causes Of Cone Crusher - fewo-am Common Failure Causes Of Cone Crusher. To prevent the oil seal from being spilled on each other thus leading to the oil leakage of the cone 4 Seal failure During the rock crushers working will come into being dust so it is necessary to equip with corresponding sealing devices in general The causes of seal failure are as follows 41 Seal damage 411 The seal is badly worn

The Common Failures and Solutions of Hydraulic Cone Crusher

Cone crusher work due to the moving cone grinding, and inadequate spring pressure often appear all sorts of fault, our experts through many years of practical experience is summarized the several common failure and analyze all kinds of fault causes and solutions. So today we will talk about something about them.

Common failures and solutions of cone crusher - Sanme

Troubleshooting method: stop and check the straight bushing and cone bushing to find out the cause of the fault and clear it. Fault 5: The oil temperature rises at the same time as the oil pressure rises. Causes of the failure: The oil pipe or the internal oil circuit of the crusher is blocked Troubleshooting method: stop and find the blockage At present, the common cone crushers are mainly the single toggle cone crusher and compound cone crusher (Symons cone crusher). Although both types of cone crushers are totally different, they have the same operation procedure. The operation procedure of cone crusher can be divided into four stages: before the start, at start-up, at run time and turning-off time. All conditions should be paid attention in each stage, and the potential problems can be found and solved timely and the service time can be prolonged. See full list on Maintenance plays an important role in the whole operation. Maintaining the crusher machine rationally can maximize the working efficiency, and here are the maintenance tips of the main parts. See full list on There are ten common faults and their corresponding solutions, which will be very helpful for you. 1. The oil indicator shows no oil flow, but the oil pressure is lower than 0.5 MPa.Reason: the oil temperature is too low; the switch of oil is turning off; the oil pump doesn’t work well.Solution: heat the oil; turn on the oil switch; turn off the crusher and change the oil pump. 2. There is an oil pressure difference between the oil pipes of the filter.Reason: The filter is blocked.Solution: if the difference is more than 0.04 MPa, the filter must be cleaned well. 3. As the oil pressure increases, so does the oil temperature.Reason: there is something wrong with the sleeve of the oil pipe.Solution: check the straight sleeve and cone sleeve after turning off the crusher, and find the problem to solve it. 4. The scavenge oil in the fuel tank is significantly reduced.Reason: the oil leaks from the bottom of the crusher; oil leaks from the flange plate.Solution: turn off the crusher, che See full list on The use of oil in the cone crusher generally only decreases, but sometimes the oil level rises strangely. The root cause is mainly caused by water in the oil tank. So what are the reasons for the water in the oil tank? 1.

Cone Crusher Frequent Problems And Solutions

Since the materials fed into cone crusher are unevenly and there will form a right angle in the transition area of hopper and feed opening, which may cause the block, especially when the moisture content of materials changes. To solve this problem, we can add a tilted arc lining plate before the hopper to make the materials can slid into the feed opening.